Free MOT Check →Full MOT history & mileage Service History £6.99 →Full refund if no data found Full Car Check £7.49 →Crashed, financed & ownership data by Experian
NG10 CNC

2010 Vauxhall Corsa · Diesel · 1248cc

Black Registered in Newcastle, North · 16 years old

Vehicle summary

MakeVauxhall
ModelCorsa
Year2010
FuelDiesel
Engine1248cc
ColourBlack
ULEZ (est.)Likely Non-compliantDiesel pre-2015
Est. Annual Tax£130–£165

ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.

At a glance

This 2010 Vauxhall Corsa Diesel 1248cc has had 9 MOT tests on record, passing 5 and failing 4 (56% pass rate). It has 94,996 miles on the clock, averaging 11,020 miles per year, above the UK average of 7,400. Common Vauxhall Corsa issues include electric power steering (eps) failure and parking brake (handbrake) failure.

MOT & Mileage History for NG10 CNC

MOT Status
Due date passed
94,996
Last Mileage
Recorded
9
Total Tests
Since 2013
56%
Pass Rate
5 passed, 4 failed

Data from DVSA. Last updated August 2026. Check gov.uk for the latest.

4

MOT failures recorded

Out of 9 tests on record
11,020

Average miles/year

Above UK average of 7,400
0

Gaps in MOT history

No gaps detected in MOT coverage

Mileage Analysis

Above average
Latest reading94,996 miles
Reading date
Average per year11,020
Mileage consistencyConsistent
Mileage over time for NG10 CNC 52k63k73k84k95k '13'17'15

Check NG10 CNC

Full MOT Test History 9 tests on record

PASS
Mileage94,996 miles
Since last MOTRetest
FAIL
Mileage94,996 miles
Since last MOT+7,071 miles
PASS
Mileage87,925 miles
Since last MOTRetest
FAIL
Mileage87,925 miles
Since last MOT+9,363 miles
PASS
Mileage78,562 miles
Since last MOTRetest
FAIL
Mileage78,562 miles
Since last MOT+12,402 miles
PASS
Mileage66,160 miles
Since last MOTRetest
FAIL
Mileage66,160 miles
Since last MOT+14,184 miles
PASS
Mileage51,976 miles

Similar cars to consider

Buyers comparing the Vauxhall Corsa often also look at these models. Check their MOT history and reliability before deciding:

🔧 Reported issues for this Vauxhall Corsa

These are the most commonly reported problems on Vauxhall Corsa models (2006–2014), based on owner reports and workshop data across the UK.

Electric power steering (EPS) failure

Electric power steering motor or column module fails, often due to water ingress or worn sensors in the steering rack/column. · Typical repair: £400-£800 (new rack/module + labour at indie garage; estimated).

Parking brake (handbrake) failure

Handbrake cable stretches/loosens, rivets on lever come adrift, or mounting clips fail; wrong-spec cables on early builds. · Typical repair: £150-£350 (new cable/lever adjust + labour; estimated).

Central locking/electrical gremlins (door locks & body electrics)

Deadlock actuators or wiring in doors fail (water ingress common); affects all doors/boot. · Typical repair: £100-£250 per door (actuator + labour; estimated).

Rear wheel bearing wear

Water enters rear wheel bearings via poor seals, causing premature failure. · Typical repair: £120-£250 per side (bearing + labour; estimated).

Read our Vauxhall Corsa Buyer's Guide →

Common faults, what to check, and what to pay

Explore more about the Vauxhall Corsa

Thinking about buying this car? These resources will help you make an informed decision.

Vehicle Details

RegistrationNG10 CNC
MakeVauxhall
ModelCorsa
ColourBlack
Fuel typeDiesel
Engine1248cc
Year2010
First registered
Area codeNG — Newcastle, North
Age identifier10 — March 2010 to August 2010

More NG10 C plates

Browse all NG10 C registrations from Newcastle.

About NG10 CNC

What car is NG10 CNC?

NG10 CNC is an black Vauxhall Corsa, diesel (1248cc). First registered in Newcastle in 2010.

What is the mileage of NG10 CNC?

The last recorded mileage for NG10 CNC was 94,996 miles, recorded on 17 May 2017 during its most recent MOT test.

Has NG10 CNC passed its MOT?

NG10 CNC has had 9 MOT tests with a 56% pass rate (5 passes, 4 failures). It last passed on 17 May 2017.

Is NG10 CNC ULEZ compliant?

Based on its fuel type and registration year, NG10 CNC is likely not ULEZ compliant. As a diesel vehicle registered in 2010, it typically does not meet the Euro 6 emission standard required. This is an estimate — confirm with TfL's ULEZ checker.

How old is NG10 CNC?

NG10 CNC is approximately 16 years old. Age identifier 10 means registered between 1 March 2010 and 31 August 2010.