Free MOT Check →Full MOT history & mileage Service History £6.99 →Full refund if no data found Full Car Check £7.49 →Crashed, financed & ownership data by Experian
KF57 CNC

2008 Vauxhall Corsa · Petrol · 1364cc

Black Registered in Northampton, Luton and Northampton · 18 years old

Vehicle summary

MakeVauxhall
ModelCorsa
Year2008
FuelPetrol
Engine1364cc
ColourBlack
ULEZ (est.)Likely CompliantPetrol post-2005 (Euro 4)
Est. Annual Tax£130–£165

ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.

At a glance

This 2008 Vauxhall Corsa Petrol 1364cc has had 7 MOT tests on record, passing 5 and failing 2 (71% pass rate). It has 65,984 miles on the clock, averaging 11,216 miles per year, above the UK average of 7,400. Common Vauxhall Corsa issues include electric power steering (eps) failure and parking brake (handbrake) failure.

MOT & Mileage History for KF57 CNC

MOT Status
Due date passed
65,984
Last Mileage
Recorded
7
Total Tests
Since 2011
71%
Pass Rate
5 passed, 2 failed

Data from DVSA. Last updated August 2026. Check gov.uk for the latest.

2

MOT failures recorded

Out of 7 tests on record
11,216

Average miles/year

Above UK average of 7,400
0

Gaps in MOT history

No gaps detected in MOT coverage

Mileage Analysis

Above average
Latest reading65,984 miles
Reading date
Miles last year13,852
Average per year11,216
Mileage consistencyConsistent
Mileage over time for KF57 CNC 21k32k44k55k66k '11'15'13

Check KF57 CNC

Full MOT Test History 7 tests on record

PASS
Mileage65,984 miles
Since last MOT+13,852 miles
PASS
Mileage52,132 miles
Since last MOT+12,305 miles
PASS
Mileage39,827 miles
Since last MOTRetest
FAIL
Mileage39,827 miles
Since last MOT+10,562 miles
PASS
Mileage29,265 miles
Since last MOT+54 miles
FAIL
Mileage29,211 miles
Since last MOT+8,021 miles
PASS
Mileage21,190 miles

Similar cars to consider

Buyers comparing the Vauxhall Corsa often also look at these models. Check their MOT history and reliability before deciding:

🔧 Reported issues for this Vauxhall Corsa

These are the most commonly reported problems on Vauxhall Corsa models (2006–2014), based on owner reports and workshop data across the UK.

Electric power steering (EPS) failure

Electric power steering motor or column module fails, often due to water ingress or worn sensors in the steering rack/column. · Typical repair: £400-£800 (new rack/module + labour at indie garage; estimated).

Parking brake (handbrake) failure

Handbrake cable stretches/loosens, rivets on lever come adrift, or mounting clips fail; wrong-spec cables on early builds. · Typical repair: £150-£350 (new cable/lever adjust + labour; estimated).

Central locking/electrical gremlins (door locks & body electrics)

Deadlock actuators or wiring in doors fail (water ingress common); affects all doors/boot. · Typical repair: £100-£250 per door (actuator + labour; estimated).

Rear wheel bearing wear

Water enters rear wheel bearings via poor seals, causing premature failure. · Typical repair: £120-£250 per side (bearing + labour; estimated).

Read our Vauxhall Corsa Buyer's Guide →

Common faults, what to check, and what to pay

Explore more about the Vauxhall Corsa

Thinking about buying this car? These resources will help you make an informed decision.

Vehicle Details

RegistrationKF57 CNC
MakeVauxhall
ModelCorsa
ColourBlack
Fuel typePetrol
Engine1364cc
Year2008
First registered
Area codeKF — Northampton, Luton and Northampton
Age identifier57 — September 2007 to February 2008

More KF57 C plates

Browse all KF57 C registrations from Northampton.

About KF57 CNC

What car is KF57 CNC?

KF57 CNC is a black Vauxhall Corsa, petrol (1364cc). First registered in Northampton in 2008.

What is the mileage of KF57 CNC?

The last recorded mileage for KF57 CNC was 65,984 miles, recorded on 2 Feb 2015 during its most recent MOT test.

Has KF57 CNC passed its MOT?

KF57 CNC has had 7 MOT tests with a 71% pass rate (5 passes, 2 failures). It last passed on 2 Feb 2015.

Is KF57 CNC ULEZ compliant?

Based on its fuel type and registration year, KF57 CNC is likely ULEZ compliant. Petrol post-2005 (Euro 4). This is an estimate based on typical emission standards — confirm with TfL's ULEZ checker for a definitive answer.

How old is KF57 CNC?

KF57 CNC is approximately 18 years old. Age identifier 57 means registered between 1 September 2007 and 28 February 2008.