Vehicle summary
ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.
At a glance
This 2010 Vauxhall Corsa Petrol 1229cc has had 11 MOT tests on record, passing 10 and failing once (91% pass rate). It has 107,485 miles on the clock, averaging 9,818 miles per year, above the UK average of 7,400. The 1.2 Twinport engine is known for 1. timing chain tensioner wear & premature chain stretch and 2. ignition coil pack failure. Common Vauxhall Corsa issues include electric power steering (eps) failure and parking brake (handbrake) failure.
MOT & Mileage History for DG60 CNC
Data from DVSA. Last updated August 2026. Check gov.uk for the latest.
MOT failure recorded
Average miles/year
Gaps in MOT history
Mileage Analysis
Above average| Latest reading | 107,485 miles |
| Reading date | |
| Miles last year | 3,801 |
| Average per year | 9,818 |
| Mileage consistency | Variable |
Check DG60 CNC
- Write-off & insurance claims Experian
- Outstanding finance check Experian
- Stolen vehicle check Experian
- Ownership changes Experian
- Mileage discrepancy alerts
- Plate & colour change history
- Franchised dealer records
- Independent garage visits
- Service interval analysis
- Warranty work logged
Full MOT Test History 11 tests on record
Similar cars to consider
Buyers comparing the Vauxhall Corsa often also look at these models. Check their MOT history and reliability before deciding:
Reported issues for this Vauxhall Corsa
These are the most commonly reported problems on Vauxhall Corsa models (2006–2014), based on owner reports and workshop data across the UK.
Electric power steering (EPS) failure
Electric power steering motor or column module fails, often due to water ingress or worn sensors in the steering rack/column. · Typical repair: £400-£800 (new rack/module + labour at indie garage; estimated).
Parking brake (handbrake) failure
Handbrake cable stretches/loosens, rivets on lever come adrift, or mounting clips fail; wrong-spec cables on early builds. · Typical repair: £150-£350 (new cable/lever adjust + labour; estimated).
Central locking/electrical gremlins (door locks & body electrics)
Deadlock actuators or wiring in doors fail (water ingress common); affects all doors/boot. · Typical repair: £100-£250 per door (actuator + labour; estimated).
Rear wheel bearing wear
Water enters rear wheel bearings via poor seals, causing premature failure. · Typical repair: £120-£250 per side (bearing + labour; estimated).
1. Timing Chain Tensioner Wear & Premature Chain Stretch
The hydraulic timing chain tensioner bleeds off pressure overnight and cannot maintain proper tension on the chain. With neglected oil changes or poor-quality oil, the chain itself stretches prematurely.[1] The tensioner guide becomes worn, allowing excessive chain slack.[3]
2. Ignition Coil Pack Failure
Heat cycling makes the plastic housing brittle; moisture corrodes internal spring contacts, causing electrical failure. Corrosion often initiates at cylinder 4.[1]
Common faults, what to check, and what to pay
Explore more about the Vauxhall Corsa
Thinking about buying this car? These resources will help you make an informed decision.
Vehicle Details
| Registration | DG60 CNC |
| Make | Vauxhall |
| Model | Corsa |
| Colour | Blue |
| Fuel type | Petrol |
| Engine | 1229cc |
| Year | 2010 |
| First registered | |
| Area code | DG — Chester, Deeside to Shrewsbury |
| Age identifier | 60 — September 2010 to February 2011 |
More DG60 C plates
Browse all DG60 C registrations from Chester.
About DG60 CNC
What car is DG60 CNC?
DG60 CNC is a blue Vauxhall Corsa, petrol (1229cc). First registered in Chester in 2010.
What is the mileage of DG60 CNC?
The last recorded mileage for DG60 CNC was 107,485 miles, recorded on 26 Sep 2022 during its most recent MOT test.
Has DG60 CNC passed its MOT?
DG60 CNC has had 11 MOT tests with an 91% pass rate (10 passes, 1 failure). It last passed on 26 Sep 2022.
Is DG60 CNC ULEZ compliant?
Based on its fuel type and registration year, DG60 CNC is likely ULEZ compliant. Petrol post-2005 (Euro 4). This is an estimate based on typical emission standards — confirm with TfL's ULEZ checker for a definitive answer.
How old is DG60 CNC?
DG60 CNC is approximately 16 years old. Age identifier 60 means registered between 1 September 2010 and 28 February 2011.