Free MOT Check →Full MOT history & mileage Service History £6.99 →Full refund if no data found Full Car Check £7.49 →Crashed, financed & ownership data by Experian
KK16 CNC

2016 Ford Focus · Diesel · 1499cc

Silver Registered in Northampton, Luton and Northampton · 10 years old

Vehicle summary

MakeFord
ModelFocus
Year2016
FuelDiesel
Engine1499cc
ColourSilver
ULEZ (est.)Likely CompliantDiesel post-2015 (Euro 6)
Est. Annual Tax£165–£265

ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.

At a glance

This 2016 Ford Focus Diesel 1499cc has had 8 MOT tests on record, passing every one. It has 82,981 miles on the clock, averaging 6,418 miles per year, below the UK average of 7,400. The 1.5 TDCi engine is known for head gasket and timing belt (cambelt). Common Ford Focus issues include door latch failure and squeaky door seals / a-pillar noise.

MOT & Mileage History for KK16 CNC

Valid
MOT Status
Expires
82,981
Last Mileage
Recorded
8
Total Tests
Since 2019
100%
Pass Rate
8 passed, 0 failed ✓

Data from DVSA. Last updated August 2026. Check gov.uk for the latest.

0

MOT failures recorded

Out of 8 tests on record
6,418

Average miles/year

Below UK average of 7,400
0

Gaps in MOT history

No gaps detected in MOT coverage

Mileage Analysis

Below average
Latest reading82,981 miles
Reading date
Miles last year1,536
Average per year6,418
Mileage consistencyVariable
Mileage over time for KK16 CNC 43k53k63k73k83k '19'25'22

Check KK16 CNC

Full MOT Test History 8 tests on record

PASS
Mileage82,981 miles
Since last MOT+1,536 miles
PASS
Mileage81,445 miles
Since last MOT+2,769 miles
PASS
Mileage78,676 miles
Since last MOT+5,624 miles
PASS
Mileage73,052 miles
Since last MOT+1,068 miles
PASS
Mileage71,984 miles
Since last MOT+11,958 miles
PASS
Mileage60,026 miles
Since last MOT+9,069 miles
PASS
Mileage50,957 miles
Since last MOT+8,421 miles
PASS
Mileage42,536 miles

Similar cars to consider

Buyers comparing the Ford Focus often also look at these models. Check their MOT history and reliability before deciding:

🔧 Reported issues for this Ford Focus

These are the most commonly reported problems on Ford Focus models (2011–2018), based on owner reports and workshop data across the UK.

Door Latch Failure

Pawl spring tab fractures, causing doors to unlatch unexpectedly while driving. · Typical repair: Free if under DVSA recall R/2015/173 (or Ford 15S26); otherwise £200-£400 per door at indie garage.

Squeaky Door Seals / A-Pillar Noise

Seals loosen or degrade, allowing wind noise and vibration. · Typical repair: £50-£150 (new seals + labour).

Excessive Battery Discharge / BCM Water Ingress

Washer fluid leaks down wires into BCM, causing drain and fault codes. · Typical repair: £100-£250 (clean BCM + new pump if needed).

Powershift Gearbox Jerking/Shuddering (Auto Variants Only)

Clutch wear or sensor failure causes harsh shifts. · Typical repair: £400-£1,500 (sensor/clutch pack).

Head Gasket

Timing Belt (Cambelt)

Read our Ford Focus Buyer's Guide →

Common faults, what to check, and what to pay

Explore more about the Ford Focus

Thinking about buying this car? These resources will help you make an informed decision.

Vehicle Details

RegistrationKK16 CNC
MakeFord
ModelFocus
ColourSilver
Fuel typeDiesel
Engine1499cc
Year2016
First registered
Area codeKK — Northampton, Luton and Northampton
Age identifier16 — March 2016 to August 2016

More KK16 C plates

Browse all KK16 C registrations from Northampton.

About KK16 CNC

What car is KK16 CNC?

KK16 CNC is a silver Ford Focus, diesel (1499cc). First registered in Northampton in 2016.

What is the mileage of KK16 CNC?

The last recorded mileage for KK16 CNC was 82,981 miles, recorded on 4 Dec 2025 during its most recent MOT test.

Has KK16 CNC passed its MOT?

KK16 CNC has had 8 MOT tests with an 100% pass rate (8 passes, 0 failures). It last passed on 4 Dec 2025.

Is KK16 CNC ULEZ compliant?

Based on its fuel type and registration year, KK16 CNC is likely ULEZ compliant. Diesel post-2015 (Euro 6). This is an estimate based on typical emission standards — confirm with TfL's ULEZ checker for a definitive answer.

How old is KK16 CNC?

KK16 CNC is approximately 10 years old. Age identifier 16 means registered between 1 March 2016 and 31 August 2016.