Free MOT Check →Full MOT history & mileage Service History £6.99 →Full refund if no data found Full Car Check £7.49 →Crashed, financed & ownership data by Experian
GJ13 CNC

2013 Ford Focus · Petrol · 1596cc

White Registered in Maidstone, Garden of England · 13 years old

Vehicle summary

MakeFord
ModelFocus
Year2013
FuelPetrol
Engine1596cc
ColourWhite
ULEZ (est.)Likely CompliantPetrol post-2005 (Euro 4)
Est. Annual Tax£165–£265

ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.

At a glance

This 2013 Ford Focus Petrol 1596cc has had 12 MOT tests on record, passing 10 and failing 2 (83% pass rate). It has 86,121 miles on the clock, averaging 6,097 miles per year, below the UK average of 7,400. Common Ford Focus issues include door latch failure and squeaky door seals / a-pillar noise.

MOT & Mileage History for GJ13 CNC

MOT Status
Due date passed
86,121
Last Mileage
Recorded
12
Total Tests
Since 2016
83%
Pass Rate
10 passed, 2 failed

Data from DVSA. Last updated August 2026. Check gov.uk for the latest.

2

MOT failures recorded

Out of 12 tests on record
6,097

Average miles/year

Below UK average of 7,400
1

Gap in MOT history

Periods with no valid MOT — may have been SORN or untaxed

Mileage Analysis

Below average
Latest reading86,121 miles
Reading date
Miles last year18
Average per year6,097
Mileage consistencyVariable
Mileage over time for GJ13 CNC 30k44k58k72k86k '16'25'22

Check GJ13 CNC

Full MOT Test History 12 tests on record

PASS
Mileage86,121 miles
Since last MOT+18 miles
FAIL
Mileage86,103 miles
Since last MOT+8,218 miles
PASS
Mileage77,885 miles
Since last MOT+2,077 miles
PASS
Mileage75,808 miles
Since last MOT+6,986 miles
PASS
Mileage68,822 miles
Since last MOT+7 miles
FAIL
Mileage68,815 miles
Since last MOT+6,675 miles
PASS
Mileage62,140 miles
Since last MOT+5,000 miles
PASS
Mileage57,140 miles
Since last MOT+6,476 miles
PASS
Mileage50,664 miles
Since last MOT+4,920 miles
PASS
Mileage45,744 miles
Since last MOT+8,637 miles
PASS
Mileage37,107 miles
Since last MOT+6,638 miles
PASS
Mileage30,469 miles

Similar cars to consider

Buyers comparing the Ford Focus often also look at these models. Check their MOT history and reliability before deciding:

🔧 Reported issues for this Ford Focus

These are the most commonly reported problems on Ford Focus models (2011–2018), based on owner reports and workshop data across the UK.

Door Latch Failure

Pawl spring tab fractures, causing doors to unlatch unexpectedly while driving. · Typical repair: Free if under DVSA recall R/2015/173 (or Ford 15S26); otherwise £200-£400 per door at indie garage.

Squeaky Door Seals / A-Pillar Noise

Seals loosen or degrade, allowing wind noise and vibration. · Typical repair: £50-£150 (new seals + labour).

Excessive Battery Discharge / BCM Water Ingress

Washer fluid leaks down wires into BCM, causing drain and fault codes. · Typical repair: £100-£250 (clean BCM + new pump if needed).

Powershift Gearbox Jerking/Shuddering (Auto Variants Only)

Clutch wear or sensor failure causes harsh shifts. · Typical repair: £400-£1,500 (sensor/clutch pack).

Read our Ford Focus Buyer's Guide →

Common faults, what to check, and what to pay

Explore more about the Ford Focus

Thinking about buying this car? These resources will help you make an informed decision.

Vehicle Details

RegistrationGJ13 CNC
MakeFord
ModelFocus
ColourWhite
Fuel typePetrol
Engine1596cc
Year2013
First registered
Area codeGJ — Maidstone, Garden of England
Age identifier13 — March 2013 to August 2013

More GJ13 C plates

Browse all GJ13 C registrations from Maidstone.

About GJ13 CNC

What car is GJ13 CNC?

GJ13 CNC is a white Ford Focus, petrol (1596cc). First registered in Maidstone in 2013.

What is the mileage of GJ13 CNC?

The last recorded mileage for GJ13 CNC was 86,121 miles, recorded on 1 May 2025 during its most recent MOT test.

Has GJ13 CNC passed its MOT?

GJ13 CNC has had 12 MOT tests with an 83% pass rate (10 passes, 2 failures). It last passed on 1 May 2025.

Is GJ13 CNC ULEZ compliant?

Based on its fuel type and registration year, GJ13 CNC is likely ULEZ compliant. Petrol post-2005 (Euro 4). This is an estimate based on typical emission standards — confirm with TfL's ULEZ checker for a definitive answer.

How old is GJ13 CNC?

GJ13 CNC is approximately 13 years old. Age identifier 13 means registered between 1 March 2013 and 31 August 2013.