Free MOT Check →Full MOT history & mileage Service History £6.99 →Full refund if no data found Full Car Check £7.49 →Crashed, financed & ownership data by Experian
CY64 CNC

2015 Ford Focus · Diesel · 1499cc

Brown Registered in Bangor, Cymru (Wales) · 11 years old

Vehicle summary

MakeFord
ModelFocus
Year2015
FuelDiesel
Engine1499cc
ColourBrown
ULEZ (est.)Likely Non-compliantDiesel pre-2015
Est. Annual Tax£165–£265

ULEZ status is estimated based on fuel type and registration year. It may not reflect the actual emission standard of this vehicle. Check with TfL for a definitive answer.

At a glance

This 2015 Ford Focus Diesel 1499cc has had 9 MOT tests on record, passing every one. It has 58,410 miles on the clock, averaging 4,737 miles per year, well below the UK average of 7,400. The 1.5 TDCi engine is known for head gasket and timing belt (cambelt). Common Ford Focus issues include door latch failure and squeaky door seals / a-pillar noise.

MOT & Mileage History for CY64 CNC

Valid
MOT Status
Expires
58,410
Last Mileage
Recorded
9
Total Tests
Since 2017
100%
Pass Rate
9 passed, 0 failed ✓

Data from DVSA. Last updated August 2026. Check gov.uk for the latest.

0

MOT failures recorded

Out of 9 tests on record
4,737

Average miles/year

Below UK average of 7,400
1

Gap in MOT history

Periods with no valid MOT — may have been SORN or untaxed

Mileage Analysis

Low mileage
Latest reading58,410 miles
Reading date
Miles last year2,088
Average per year4,737
Mileage consistencyVariable
Mileage over time for CY64 CNC 20k29k39k49k58k '17'26'22

Check CY64 CNC

Full MOT Test History 9 tests on record

PASS
Mileage58,410 miles
Since last MOT+2,088 miles
PASS
Mileage56,322 miles
Since last MOT+3,463 miles
PASS
Mileage52,859 miles
Since last MOT+4,602 miles
PASS
Mileage48,257 miles
Since last MOT+6,045 miles
PASS
Mileage42,212 miles
Since last MOT+4,986 miles
PASS
Mileage37,226 miles
Since last MOT+1,228 miles
PASS
Mileage35,998 miles
Since last MOT+9,396 miles
PASS
Mileage26,602 miles
Since last MOT+6,914 miles
PASS
Mileage19,688 miles

Similar cars to consider

Buyers comparing the Ford Focus often also look at these models. Check their MOT history and reliability before deciding:

🔧 Reported issues for this Ford Focus

These are the most commonly reported problems on Ford Focus models (2011–2018), based on owner reports and workshop data across the UK.

Door Latch Failure

Pawl spring tab fractures, causing doors to unlatch unexpectedly while driving. · Typical repair: Free if under DVSA recall R/2015/173 (or Ford 15S26); otherwise £200-£400 per door at indie garage.

Squeaky Door Seals / A-Pillar Noise

Seals loosen or degrade, allowing wind noise and vibration. · Typical repair: £50-£150 (new seals + labour).

Excessive Battery Discharge / BCM Water Ingress

Washer fluid leaks down wires into BCM, causing drain and fault codes. · Typical repair: £100-£250 (clean BCM + new pump if needed).

Powershift Gearbox Jerking/Shuddering (Auto Variants Only)

Clutch wear or sensor failure causes harsh shifts. · Typical repair: £400-£1,500 (sensor/clutch pack).

Head Gasket

Timing Belt (Cambelt)

Read our Ford Focus Buyer's Guide →

Common faults, what to check, and what to pay

Explore more about the Ford Focus

Thinking about buying this car? These resources will help you make an informed decision.

Vehicle Details

RegistrationCY64 CNC
MakeFord
ModelFocus
ColourBrown
Fuel typeDiesel
Engine1499cc
Year2015
First registered
Area codeCY — Bangor, Cymru (Wales)
Age identifier64 — September 2014 to February 2015

More CY64 C plates

Browse all CY64 C registrations from Bangor.

About CY64 CNC

What car is CY64 CNC?

CY64 CNC is a brown Ford Focus, diesel (1499cc). First registered in Bangor in 2015.

What is the mileage of CY64 CNC?

The last recorded mileage for CY64 CNC was 58,410 miles, recorded on 2 Mar 2026 during its most recent MOT test.

Has CY64 CNC passed its MOT?

CY64 CNC has had 9 MOT tests with an 100% pass rate (9 passes, 0 failures). It last passed on 2 Mar 2026.

Is CY64 CNC ULEZ compliant?

Based on its fuel type and registration year, CY64 CNC is likely not ULEZ compliant. As a diesel vehicle registered in 2015, it typically does not meet the Euro 6 emission standard required. This is an estimate — confirm with TfL's ULEZ checker.

How old is CY64 CNC?

CY64 CNC is approximately 11 years old. Age identifier 64 means registered between 1 September 2014 and 28 February 2015.