Home/Car check/Hyundai/Iload

Hyundai Iload car check

Find out if a Iload has outstanding finance, has been written off or stolen, how many owners it’s had, and which known problems apply to the generation you’re looking at.

Finance, stolen, write-off and owner history data provided by Experian. Results in under a minute.

MOT failure rate
27.8%7k tests
Known problems
5across TQ
Full report
£7.49one-off, no subscription

Which Iload are you looking at?

Each Iload generation has its own weak spots. Here are the known problems.

  1. Rear leaf spring failure

    Safety risk TQ

    The rear leaf spring assemblies on the iLoad are prone to fracturing or serious weakening, particularly in the main leaf or secondary leaves. This commercial van uses a multi-leaf spring setup to handle payload, but the springs appear undersized for typical UK commercial use patterns. MOT data shows this model fails spring inspections at 905 times the national fleet average, making it the most documented structural weakness on this vehicle. Failure can cause sudden loss of load-carrying capacity and dangerous handling characteristics.

    What to check: Walk around the rear of the vehicle and look for any visible sagging on one side compared to the other - this indicates leaf spring failure on the low side. Get down and visually inspect each rear leaf spring assembly for cracks, fractures, or broken leaves. Look specifically where the main leaf ...

  2. Rear suspension bush and joint wear

    Wear item TQ

    The rear suspension mounting bushes and joints wear excessively on the iLoad, with MOT failures occurring at 152 times the national average. The commercial vehicle's rear axle assembly uses rubber bushes that deteriorate rapidly under heavy loading and commercial use patterns. Worn bushes affect handling, cause irregular tyre wear, and can lead to MOT failure. This affects the leaf spring mounting points, shock absorber bushes, and axle location components.

    What to check: Inspect the rear suspension bushes visually - look for cracked, split, or obviously deteriorated rubber components around the leaf spring eyes and shock absorber mountings. Check for excessive rust or corrosion around metal suspension components that may indicate bush failure allowing movement an...

  3. Driveshaft bearing wear

    Wear item TQ

    The driveshaft centre bearing (propshaft bearing) wears excessively on high-mileage iLoad vehicles, with MOT failures at 40 times the fleet average. This rubber-mounted bearing supports the two-piece propshaft and is subject to constant rotation and vibration. Commercial use with frequent stop-start driving and heavy loading accelerates bearing deterioration. Failure causes vibration, noise, and can lead to complete driveshaft separation if left unrepaired.

    What to check: Inspect underneath the vehicle along the driveshaft for any obvious damage to the centre bearing housing or rubber mounting - look for splits, cracks, or oil contamination of the rubber mount. Check for any play by trying to move the driveshaft vertically at the centre bearing location - there sh...

  4. Brake caliper binding and seizure

    Safety and MOT risk TQ

    Brake calipers on the iLoad are prone to binding and seizure, with MOT data showing brake binding failures at 5.8 times the fleet average. Commercial vehicle brake systems work harder than passenger cars, and the caliper slide pins and pistons can seize due to corrosion, dirt ingress, or lack of maintenance. Binding brakes cause uneven brake pad wear, reduced braking efficiency, overheating, and potential brake fade under heavy use.

    What to check: Check each wheel for signs of brake binding - look at the brake discs for discoloration, scoring, or obvious overheating marks that appear as blue or brown staining on the metal. Examine the brake pads through the caliper if visible - binding causes uneven wear with one pad significantly thinner ...

  5. Parking brake adjustment problems

    Safety and MOT risk TQ

    The parking brake system on the iLoad frequently requires adjustment, with MOT failures for parking brake efficiency and excessive lever movement occurring at up to 10.6 times the fleet average. The cable-operated rear drum parking brake system stretches over time and with heavy commercial use. Poor adjustment causes MOT failure and reduced parking brake effectiveness on slopes, which is critical for commercial vehicle safety when loading or unloading.

    What to check: Pull the parking brake lever and count the clicks - it should engage within 3-7 clicks for most vehicles. If it requires more than 8-10 clicks to hold the vehicle, the adjustment is incorrect. With the parking brake applied, try to push the vehicle by hand on level ground - it should not move if ...

Iload MOT results

27.8%

of Iload MOT tests end in a fail, from 7,384 tests.

Most common reasons for failing

  1. Coil springs brokenSuspension
  2. Transmission shaft bearing wornBodywork
  3. Transmission shaft flexible coupling deterioratedBodywork

Check the Iload you’re buying

One report covers outstanding finance, write-offs, theft and previous owners from Experian, plus MOT history, mileage and the known problems for its generation.

Finance, stolen, write-off and owner history data provided by Experian.

What the check includes

Iload questions

Is the Hyundai Iload reliable?

27.8% of Iload models fail their MOT based on 7,384 tests analysed. That’s below average for the class. There are 5 known problems to watch for, the most serious being rear leaf spring failure. A full history check shows whether a specific car has had related write-offs or insurance claims.

What are the main problems with a Hyundai Iload?

The most serious known issues are rear leaf spring failure, rear suspension bush and joint wear, driveshaft bearing wear. Our car check flags whether a specific Iload has been written off or had insurance claims linked to these faults.

How do I check if a Hyundai Iload has outstanding finance?

Enter the registration on this page. We query Experian’s finance database and return any outstanding agreements within a minute. If finance is still owed, the finance company can legally repossess the car even after you’ve paid the seller. At £7.49, you can check before you buy.

How do I check if a Hyundai Iload has been written off?

Our check queries Experian’s insurance write-off database for Cat A, B, S and N markers. A Cat S or N Iload has been structurally or non-structurally damaged and repaired. This doesn’t mean it’s unsafe, but it affects resale value and some insurers won’t cover it. The check costs £7.49.

Can I check a Hyundai Iload for free?

You can check MOT history free on GOV.UK, which shows past test results and advisories. What it won’t show is outstanding finance, write-offs or theft markers, which are the things that actually cost you money after you’ve bought. Our full check adds all of that for £7.49, using Experian data.

What does a Hyundai Iload fail its MOT on?

The most common MOT failure on the Iload is coil springs broken. 27.8% of Iload models fail overall, based on 7,384 tests. Checking a car’s full MOT history before buying shows you recurring problems the seller might not mention.

More on the Iload

Other Hyundai car checks

Finance, stolen, write-off and owner history data provided by Experian. MOT data from DVSA. Known problems from GetCarWise analysis. Updated October 2026.