Peugeot 308 car check
Find out if a Peugeot 308 has outstanding finance, has been written off or stolen, how many owners it’s had, and which known problems apply to the generation you’re looking at.
Finance, stolen, write-off and owner history data provided by Experian. Results in under a minute.
- Typical price
- £13,245898 at dealers
- MOT failure rate
- 24.4%576k tests
- Known problems
- 10across Mk1 to Mk2
- Full report
- £7.49one-off, no subscription
Which 308 are you looking at?
Each 308 generation has its own weak spots. Pick the one you’re viewing to see what to check.
-
Timing chain failure
Safety risk Mk1The EP6 1.6 THP turbo engine uses a timing chain system with known stretch and tensioner failure issues. Chain stretch of 5-8 degrees is common by 60,000 miles, causing rough idle, poor performance, and engine management lights. Complete chain failure destroys the interference engine with bent valves and piston damage. This was a widespread issue on early production cars that led to class action lawsuits in multiple countries. The issue was partially addressed in later Mk2 variants with improved tensioner design.
What to check: Listen for chain rattle from the timing case area before starting - this may be audible as metallic rattling from the front of the engine bay. Check service history for evidence of previous chain replacement or timing-related repairs. Request any diagnostic scans showing timing correlation faults...
-
Timing chain tensioner failure
Safety risk Mk1The hydraulic timing chain tensioner on EP6 THP engines fails prematurely, unable to maintain proper chain tension. This is often the root cause of timing chain stretch and failure. The tensioner uses oil pressure to maintain tension but internal seals fail, causing loss of pressure and allowing the chain to slack. Early morning startup rattle is the classic symptom before complete failure occurs. This merged entry covers both EP6 and EP6DT variants which share the same fundamental tensioner design flaw.
What to check: Listen carefully for chain rattle from cold - tensioner failure is most apparent before oil pressure builds. Check for oil leaks around the timing case which may indicate tensioner seal failure. Ask about recent rattling noises on startup that disappear after warming.
-
Timing belt (wet) issues
Safety risk Mk2The 1.2 PureTech EB2 engine uses an unconventional wet timing belt that runs inside the engine oil bath rather than a traditional dry belt. The belt material degrades in oil, causing particles to contaminate the lubrication system and block oil ways. Belt failure is catastrophic on this interference engine. The wet belt design was intended to reduce noise but has proven problematic with premature failures reported well before the 80,000-mile service interval. This is a known issue across PSA Group vehicles using this engine.
What to check: Check oil condition on dipstick for black particles or unusual contamination that might indicate belt degradation. Ask for service history showing belt replacement - many owners are unaware of this critical service. Look for any oil consumption records as belt particles can affect oil flow.
-
Water pump failure
Wear item Mk1The belt-driven water pump on 1.6 THP engines fails prematurely due to bearing wear and seal degradation. The pump is driven by the auxiliary belt system and failure typically manifests as coolant leaks from the pump housing or complete bearing seizure. This is a common failure point that often coincides with timing chain issues due to overheating damage. The pump location makes replacement moderately complex as it requires timing belt area access.
What to check: Check coolant level in header tank and look for pink/green staining around the water pump area visible from above. Inspect the ground under the car for coolant puddles, particularly pink or green fluid. Check expansion tank for contamination or oil mixing which indicates head gasket issues second...
-
DPF issues
Wear item Mk1, Mk2Diesel particulate filter blockage is endemic on Peugeot 308 diesel variants, particularly those used for short journeys. The DPF requires regular high-temperature regeneration cycles that cannot complete during urban driving. Blocked filters cause limp mode activation, excessive fuel consumption, and engine damage from back-pressure. This affects all diesel variants across both generations including 1.6 HDi (DV6), 2.0 HDi (DW10), and newer BlueHDi (DV5) engines. Euro 5 and Euro 6 variants are equally affected.
What to check: Check for DPF warning lights on the dashboard - amber DPF symbol or spanner light indicates regeneration required. Ask about recent driving patterns - cars used only for short journeys are at highest risk. Look for excessive black soot deposits around the exhaust tip indicating incomplete regener...
-
Turbo failure
Engine damage risk Mk1The Garrett GT1544V turbocharger on EP6DT engines suffers from bearing wear, actuator failure, and boost pressure issues. Common problems include wastegate actuator sticking, bearing oil seal failure causing blue smoke, and complete bearing seizure. The turbo is sensitive to oil quality and change intervals - irregular servicing accelerates failure. This often occurs alongside timing chain problems due to oil contamination from failing internal components.
What to check: Check for blue smoke staining around the exhaust tip indicating oil burning from turbo seal failure. Look for oil leaks around turbo pipework and intercooler connections. Check service history for oil change regularity - irregular changes accelerate turbo wear.
-
Dual mass flywheel failure
Wear item Mk1The dual mass flywheel on diesel variants fails due to internal spring and damper wear, causing vibration, noise, and clutch engagement problems. Symptoms include rattling during idle, vibration through the pedals and gear lever, and difficult gear selection. The DMF dampens diesel engine vibration but the internal components wear progressively. Failure often coincides with clutch replacement as both components are accessed together during repair.
What to check: With engine off, engage gear and attempt to rock the car gently - excessive free play may indicate DMF wear. Check for clutch fluid level and condition as hydraulic problems can mask DMF symptoms.
-
EGS automated manual issues
Wear item Mk1The EGS (Efficient Gear System) automated manual transmission suffers from actuator motor failure, clutch hydraulic problems, and control unit issues. This single-clutch automated system is jerky in normal operation but failure symptoms include harsh gear changes, clutch slip, inability to select gears, and transmission warning lights. The system uses hydraulic actuators controlled by the transmission ECU and failure often requires replacement of expensive actuator assemblies.
What to check: Check dashboard for transmission warning lights or fault messages. Ask about recent jerky operation or clutch smell which indicates system problems. Check transmission fluid level if accessible - low fluid affects operation.
-
EGR failure
Engine damage risk Mk1The exhaust gas recirculation valve on diesel variants becomes clogged with carbon deposits, causing rough idle, poor performance, and excessive smoke. The EGR recirculates exhaust gas to reduce NOx emissions but carbon buildup prevents proper valve operation. This is particularly problematic on cars used for short journeys where the EGR valve doesn't reach optimal operating temperature. Symptoms include rough idle, black smoke, and reduced power.
What to check: Check for excessive black soot around the exhaust pipe indicating incomplete combustion. Look for carbon deposits around the intake manifold area if visible. Ask about driving patterns - short journeys worsen EGR problems.
-
AdBlue system issues
Engine damage risk Mk2BlueHDi engines use AdBlue (DEF) injection to reduce NOx emissions but the system suffers from injector clogging, pump failure, and sensor problems. Common issues include AdBlue quality warnings, system malfunction lights, and countdown timers threatening engine shutdown. The AdBlue injector clogs with crystallised urea deposits, particularly if low-quality AdBlue is used or the tank runs empty. Temperature sensors and level sensors also fail causing system faults.
What to check: Check dashboard for AdBlue warning lights or countdown displays - system will prevent restart if depleted. Check AdBlue fluid level in tank if accessible - blue fluid should be clear, not contaminated. Ask about recent AdBlue quality or system warning messages.
We haven’t flagged any common problems for this generation in our data yet. A history check still tells you about finance, write-offs and theft, and the MOT history shows how this particular car has been looked after.
What 308s cost at dealers now
From 898 used 308s we track on UK dealer websites.
- Typical asking price
- £13,245
- Typical mileage
- 39,042 miles
- Price change vs last month
- -14.8%
308 MOT results
of 308 MOT tests end in a fail, from 575,846 tests.
Most common reasons for failing
- Transmission joint, belt or chain wornBodywork
- Emissions failureExhaust & Emissions
- Towbar faultBodywork
Check the 308 you’re buying
One report covers outstanding finance, write-offs, theft and previous owners from Experian, plus MOT history, mileage and the known problems for its generation.
Finance, stolen, write-off and owner history data provided by Experian.
What the check includes
- Outstanding finance Experian
- Write-off status Experian
- Stolen vehicle check Experian
- Previous owners and keeper history Experian
- MOT history and advisories DVSA
- Mileage check DVSA
- Known problems for its generation GetCarWise
- How many are left on the road DVLA
308 questions
Is the Peugeot 308 reliable?
24.4% of 308 models fail their MOT based on 575,846 tests analysed. That’s about average for the class. There are 10 known problems to watch for, the most serious being timing chain failure. A full history check shows whether a specific car has had related write-offs or insurance claims.
What are the main problems with a Peugeot 308?
The most serious known issues are timing chain failure, timing chain tensioner failure, timing belt (wet) issues. Problems vary by generation, so check which apply to the year you’re looking at. Our car check flags whether a specific 308 has been written off or had insurance claims linked to these faults.
How do I check if a Peugeot 308 has outstanding finance?
Enter the registration on this page. We query Experian’s finance database and return any outstanding agreements within a minute. If finance is still owed, the finance company can legally repossess the car even after you’ve paid the seller. At £7.49, you can check before you buy.
How do I check if a Peugeot 308 has been written off?
Our check queries Experian’s insurance write-off database for Cat A, B, S and N markers. A Cat S or N 308 has been structurally or non-structurally damaged and repaired. This doesn’t mean it’s unsafe, but it affects resale value and some insurers won’t cover it. The check costs £7.49.
Can I check a Peugeot 308 for free?
You can check MOT history free on GOV.UK, which shows past test results and advisories. What it won’t show is outstanding finance, write-offs or theft markers, which are the things that actually cost you money after you’ve bought. Our full check adds all of that for £7.49, using Experian data.
What does a Peugeot 308 fail its MOT on?
The most common MOT failure on the 308 is transmission joint, belt or chain worn. 24.4% of 308 models fail overall, based on 575,846 tests. Checking a car’s full MOT history before buying shows you recurring problems the seller might not mention.
More on the 308
Other Peugeot car checks
Finance, stolen, write-off and owner history data provided by Experian. MOT data from DVSA. Known problems from GetCarWise analysis. Updated October 2026.