Home/Car check/Peugeot/106

Peugeot 106 car check

Find out if a Peugeot 106 has outstanding finance, has been written off or stolen, how many owners it’s had, and which known problems apply to the generation you’re looking at.

Finance, stolen, write-off and owner history data provided by Experian. Results in under a minute.

MOT failure rate
30.6%227k tests
Known problems
5across 106_Phase1 to 106_Phase2
Full report
£7.49one-off, no subscription

Which 106 are you looking at?

Each 106 generation has its own weak spots. Pick the one you’re viewing to see what to check.

  1. Structural corrosion compromising vehicle rigidity

    Safety risk 106_Phase1, 106_Phase2

    The 106's monocoque structure is prone to serious corrosion that weakens the load-bearing shell, particularly around suspension mounting points and structural joints. MOT data shows this model fails at 58.6 times the fleet average for structural rigidity defects, with failures documented across all engine variants and mileage bands. The thin steel construction and basic anti-corrosion treatment make this a progressive issue that can render the vehicle unsafe. This is distinct from cosmetic surface rust and represents a fundamental structural weakness.

    What to check: Inspect the sill sections (running along the bottom edge of each door opening) for visible rust-through holes or areas where metal feels soft when pressed. Check the rear wheel arches from inside the boot - look for rust perforation around the suspension mounting points. Examine the floor pan und...

  2. Brake system efficiency deterioration

    Safety risk 106_Phase1, 106_Phase2

    The 106 suffers from widespread brake efficiency problems affecting both individual wheel performance and overall system effectiveness. MOT data shows brake effort inadequacy failures at 124.6 times the fleet average and system efficiency below minimum requirements at 62 times the average. The issue stems from caliper seizure, brake line corrosion, and master cylinder deterioration. This affects all variants and mileage ranges, indicating a fundamental design weakness in the brake system components and materials used.

    What to check: Check brake fluid level in the reservoir - low levels indicate leaks or worn pads. Look for brown or black fluid which suggests internal corrosion or moisture contamination. Examine brake lines under the car for corrosion, particularly where they pass through the rear axle beam and around suspens...

  3. Rear axle beam excessive movement

    Safety risk 106_Phase1, 106_Phase2

    The rear axle beam mounting system develops excessive movement between the stub axle and beam assembly, with MOT failures at 128.7 times the fleet average on 1.1-litre models at high mileage. This indicates failure of the torsion beam bearings or mounting bushes that allow the semi-independent rear suspension to articulate. The fault creates dangerous handling characteristics and can lead to loss of rear wheel control during cornering or braking. The issue is most prevalent on higher-mileage examples where bearing wear has progressed.

    What to check: Inspect the rear suspension from underneath - look for obvious damage or displacement of the rear axle beam assembly. Check for oil or grease leakage around the central torsion beam area which may indicate bearing failure. Examine the rear wheel alignment visually - excessive toe-in or toe-out su...

  4. Steering component mounting area corrosion

    Safety risk 106_Phase1, 106_Phase2

    The load-bearing structure within 30cm of steering component mounting points suffers significant corrosion, with MOT failures at 60.7 times the fleet average. This affects the areas where the steering rack and associated components attach to the body shell or subframe. Corrosion in these 'prescribed areas' is classified as dangerous because it can lead to steering component detachment and immediate loss of vehicle control. The thin steel construction and poor corrosion protection make this a critical safety issue on higher-mileage examples.

    What to check: Inspect the area around the steering rack mounting points for visible corrosion or weakened metal - this requires looking underneath the front of the car. Check the structural integrity of the front subframe where steering components mount - look for rust perforation or areas where the metal appe...

  5. Emissions system deterioration exceeding limits

    Engine damage risk 106_Phase1, 106_Phase2

    Petrol variants consistently fail emissions testing at 77.3 times the fleet average, affecting 1.1, 1.4, and 1.6-litre engines across all mileage bands. The issue stems from deterioration of the catalytic converter, lambda sensor, and carburetor or injection system calibration on older examples. The basic emissions control systems fitted to these engines are prone to component failure and require regular maintenance to meet MOT standards. This is a legal requirement for roadworthiness and affects resale value.

    What to check: Check the exhaust system for visible damage or corrosion, particularly around the catalytic converter section which should be intact with no holes or loose heat shields. Examine the lambda sensor (oxygen sensor) in the exhaust manifold - it should be securely connected with no damaged wiring. On ...

106 MOT results

30.6%

of 106 MOT tests end in a fail, from 227,283 tests.

Most common reasons for failing

  1. Braking effort inadequate at a wheelBrakes
  2. Fuel tank, pipe or hose insecureBodywork
  3. Emissions failureExhaust & Emissions

Check the 106 you’re buying

One report covers outstanding finance, write-offs, theft and previous owners from Experian, plus MOT history, mileage and the known problems for its generation.

Finance, stolen, write-off and owner history data provided by Experian.

What the check includes

106 questions

Is the Peugeot 106 reliable?

30.6% of 106 models fail their MOT based on 227,283 tests analysed. That’s below average for the class. There are 5 known problems to watch for, the most serious being structural corrosion compromising vehicle rigidity. A full history check shows whether a specific car has had related write-offs or insurance claims.

What are the main problems with a Peugeot 106?

The most serious known issues are structural corrosion compromising vehicle rigidity, brake system efficiency deterioration, rear axle beam excessive movement. Problems vary by generation, so check which apply to the year you’re looking at. Our car check flags whether a specific 106 has been written off or had insurance claims linked to these faults.

How do I check if a Peugeot 106 has outstanding finance?

Enter the registration on this page. We query Experian’s finance database and return any outstanding agreements within a minute. If finance is still owed, the finance company can legally repossess the car even after you’ve paid the seller. At £7.49, you can check before you buy.

How do I check if a Peugeot 106 has been written off?

Our check queries Experian’s insurance write-off database for Cat A, B, S and N markers. A Cat S or N 106 has been structurally or non-structurally damaged and repaired. This doesn’t mean it’s unsafe, but it affects resale value and some insurers won’t cover it. The check costs £7.49.

Can I check a Peugeot 106 for free?

You can check MOT history free on GOV.UK, which shows past test results and advisories. What it won’t show is outstanding finance, write-offs or theft markers, which are the things that actually cost you money after you’ve bought. Our full check adds all of that for £7.49, using Experian data.

What does a Peugeot 106 fail its MOT on?

The most common MOT failure on the 106 is braking effort inadequate at a wheel. 30.6% of 106 models fail overall, based on 227,283 tests. Checking a car’s full MOT history before buying shows you recurring problems the seller might not mention.

More on the 106

Other Peugeot car checks

Finance, stolen, write-off and owner history data provided by Experian. MOT data from DVSA. Known problems from GetCarWise analysis. Updated October 2026.