BMW 6 Series car check
Find out if a 6 Series has outstanding finance, has been written off or stolen, how many owners it’s had, and which known problems apply to the generation you’re looking at.
Finance, stolen, write-off and owner history data provided by Experian. Results in under a minute.
- Typical price
- £13,45776 at dealers
- MOT failure rate
- 15.3%13k tests
- Known problems
- 10across E24 to F12
- Full report
- £7.49one-off, no subscription
Which 6 Series are you looking at?
Each 6 Series generation has its own weak spots. Pick the one you’re viewing to see what to check.
-
Rod bearing failure
Safety risk E63The S85 5.0-litre V10 engine uses plain shell bearings between the connecting rods and crankshaft that are undersized for the engine's power output and rpm capability. These bearings experience accelerated wear due to oil starvation during high-rpm operation and inadequate oil flow to bearing surfaces. Rod bearing failure sends metal debris throughout the lubrication system, destroying the engine beyond economical repair. This is the same catastrophic failure mode documented extensively on the E60 M5 with identical S85 engine.
What to check: Remove the oil filler cap and examine the oil on the dipstick under strong light for any metallic sparkle or fine copper/bronze particles that indicate bearing wear. Request oil analysis reports if available - copper and lead content above 50ppm indicates bearing wear. Check service history for o...
-
Brake pipe corrosion
Safety risk E63, F06/F12BMW 6 Series models show brake pipe corrosion at 298.2 times the fleet average rate, with particular problems on V8 petrol variants where brake lines run close to exhaust manifolds and turbocharger heat shields. The combination of road salt exposure and heat cycling causes steel brake pipes to corrode internally and externally, leading to brake fluid leaks and potential brake failure. This is a safety-critical issue that causes immediate MOT failure and renders the vehicle dangerous to drive.
What to check: Inspect all visible brake lines under the car for surface corrosion, rust staining, or obvious fluid leaks - pay particular attention to areas near the exhaust system. Check brake fluid level in the reservoir - low fluid may indicate a leak in the system. Look for brake fluid staining on the insi...
-
Valve stem seal failure
Engine damage risk E63The N62 4.8-litre V8 uses rubber valve stem seals that harden and shrink with age, allowing engine oil to leak past the valve guides into the combustion chambers. This is a well-documented design weakness on all N62 engines, exacerbated by the engine's complex variable valve timing system creating higher temperatures around the cylinder heads. Oil consumption can exceed 1 litre per 1,000 miles on severely affected engines. BMW issued Technical Service Bulletin SI B11 06 05 acknowledging the problem and specifying revised seal specifications.
What to check: Pull the dipstick and check oil level - affected engines require frequent top-ups, often weekly on high-mileage examples. Look at the exhaust tailpipes for black carbon deposits indicating oil burning. Ask the seller about oil consumption rates and whether valve stem seals have been replaced. Req...
-
VANOS issues
Engine damage risk E63VANOS (Variable Nockenwellen Steuerung) is BMW's variable valve timing system using oil pressure to adjust camshaft timing for optimal performance and emissions. The system relies on small oil passages and precision solenoids that become blocked with carbon deposits from extended oil change intervals. Seals within the VANOS units deteriorate with age, causing erratic timing control that manifests as rough idle, poor cold running, and diagnostic trouble codes. Both N52 straight-six and N62 V8 engines are affected, with the V8 having two separate VANOS units.
What to check: Connect an OBD reader and check for stored codes related to camshaft position, VANOS solenoids, or timing correlation (P0015, P0020, P0021, P0025). Ask when the engine oil was last changed - VANOS problems are accelerated by extended oil change intervals. Check oil condition on dipstick - thick, ...
-
Timing chain wear
Engine damage risk F06/F12The N57 3.0-litre diesel engine uses a timing chain with hydraulic tensioners that wear prematurely due to the high compression loads and combustion pressures of the diesel engine. Chain stretch occurs when tensioner mechanisms fail to maintain proper chain tension, causing the timing chain to contact the timing chain guides and create a characteristic rattling noise. If the chain jumps timing or breaks, severe piston and valve damage results. This issue affects N57 engines across the BMW range and is well-documented by diesel specialists.
What to check: Open the bonnet and listen for any rattling noises from the front of the engine before starting - a loose chain may rattle when the engine is turned off. Check service history for timing chain replacement or tensioner replacement work. Ask specifically about any warning lights or engine managemen...
-
Rod bearing concerns
Engine damage risk F06/F12The S63 4.4-litre twin-turbo V8 engine uses connecting rod bearings that show accelerated wear patterns compared to naturally aspirated engines, likely due to the higher cylinder pressures from turbocharging and the engine's performance-focused design. While not as catastrophic as the S85 V10 bearing failures, early bearing wear on S63 engines has been documented by BMW specialists, particularly on engines that have been driven hard or maintained with extended oil change intervals. Oil analysis monitoring is recommended to detect bearing wear before catastrophic failure occurs.
What to check: Check the oil condition on the dipstick for any metallic particles or sparkle under strong light that indicates bearing wear. Request oil analysis reports if available - copper content above 30ppm suggests bearing wear is beginning. Verify oil change intervals have been maintained at 7,500 miles ...
-
Transmission flexible coupling failure
Wear item F06/F12The flexible coupling (flex disc or giubo) connects the transmission output to the propshaft on rear-wheel-drive BMW 6 Series models. This rubber and steel component absorbs driveline vibrations but deteriorates rapidly on these models, with MOT data showing failure rates 182 times higher than the fleet average. The coupling splits or tears, causing severe vibration, clunking noises during gear changes, and potential damage to the transmission or differential if left unrepaired. This affects both diesel and petrol variants across multiple mileage ranges.
What to check: Visually inspect under the car behind the gearbox for the flexible disc coupling - look for visible cracks, splits, or pieces of rubber hanging loose. Check for transmission fluid leaks around the output flange that might indicate coupling failure has damaged seals. Ask about any recent vibration...
-
Suspension pin and bush wear
Wear item E24, E63, F06/F12BMW 6 Series models across all generations suffer from accelerated wear of suspension bushes, control arm bushes, and anti-roll bar links, with MOT failure rates up to 18.7 times higher than the fleet average. The large, heavy nature of these luxury coupes places significant loads on suspension components, while the performance-oriented suspension setup uses harder bushes that crack and perish more readily than family car equivalents. Front control arm bushes and rear trailing arm bushes are particular problem areas that affect handling precision and cause MOT failures.
What to check: Visually inspect front control arm bushes behind each front wheel - look for cracked, split, or oil-contaminated rubber bushes where the arms connect to the subframe. Check rear suspension bushes visible from behind the rear wheels for similar deterioration. Look for any obvious play or movement ...
-
Suspension component corrosion
Wear item E63, F06/F12BMW 6 Series suspension components suffer from corrosion damage at 298.2 times the fleet average, particularly affecting steel control arms, subframe mounting points, and anti-roll bar mounting brackets. The combination of road salt exposure and the complex multi-link suspension design creates areas where moisture and salt accumulate, causing structural corrosion that weakens mounting points and threatens handling safety. This issue is progressive and worsens with age and exposure to winter road conditions.
What to check: Inspect visible suspension components from under the car for surface rust, flaking metal, or structural corrosion around mounting points and brackets. Pay particular attention to areas where steel components meet aluminium parts, as galvanic corrosion accelerates here. Look for rust staining or c...
-
Shock absorber failure
Wear item E63, F06/F12BMW 6 Series shock absorbers fail at 73.7 times the fleet average rate, with particular issues on petrol variants where the additional weight and performance-oriented suspension tuning place higher demands on damper components. The sophisticated multi-mode suspension systems fitted to many variants use complex dampers with electronic adjustment that are more prone to failure than conventional units. Leaking seals and worn internal components reduce damping effectiveness, causing poor ride quality and handling degradation.
What to check: Walk around the car and visually inspect each shock absorber for oil leaks, rust staining, or wetness around the damper body and mounting points. Push down firmly on each corner of the car and release - the car should return to normal ride height with minimal bouncing. Excessive bouncing indicate...
We haven’t flagged any common problems for this generation in our data yet. A history check still tells you about finance, write-offs and theft, and the MOT history shows how this particular car has been looked after.
What 6 Series cost at dealers now
From 76 used 6 Series we track on UK dealer websites.
- Typical asking price
- £13,457
- Typical mileage
- 83,035 miles
- Price change vs last month
- -9.6%
6 Series MOT results
of 6 Series MOT tests end in a fail, from 12,666 tests.
Most common reasons for failing
- Transmission shaft flexible coupling deterioratedBodywork
- Headlight faultLights & Electrics
- Any fracture or welding defect on a wheelWheels
Check the 6 Series you’re buying
One report covers outstanding finance, write-offs, theft and previous owners from Experian, plus MOT history, mileage and the known problems for its generation.
Finance, stolen, write-off and owner history data provided by Experian.
What the check includes
- Outstanding finance Experian
- Write-off status Experian
- Stolen vehicle check Experian
- Previous owners and keeper history Experian
- MOT history and advisories DVSA
- Mileage check DVSA
- Known problems for its generation GetCarWise
- How many are left on the road DVLA
6 Series questions
Is the BMW 6 Series reliable?
15.3% of 6 Series models fail their MOT based on 12,666 tests analysed. That’s about average for the class. There are 10 known problems to watch for, the most serious being rod bearing failure. A full history check shows whether a specific car has had related write-offs or insurance claims.
What are the main problems with a BMW 6 Series?
The most serious known issues are rod bearing failure, brake pipe corrosion, valve stem seal failure. Problems vary by generation, so check which apply to the year you’re looking at. Our car check flags whether a specific 6 Series has been written off or had insurance claims linked to these faults.
How do I check if a BMW 6 Series has outstanding finance?
Enter the registration on this page. We query Experian’s finance database and return any outstanding agreements within a minute. If finance is still owed, the finance company can legally repossess the car even after you’ve paid the seller. At £7.49, you can check before you buy.
How do I check if a BMW 6 Series has been written off?
Our check queries Experian’s insurance write-off database for Cat A, B, S and N markers. A Cat S or N 6 Series has been structurally or non-structurally damaged and repaired. This doesn’t mean it’s unsafe, but it affects resale value and some insurers won’t cover it. The check costs £7.49.
Can I check a BMW 6 Series for free?
You can check MOT history free on GOV.UK, which shows past test results and advisories. What it won’t show is outstanding finance, write-offs or theft markers, which are the things that actually cost you money after you’ve bought. Our full check adds all of that for £7.49, using Experian data.
What does a BMW 6 Series fail its MOT on?
The most common MOT failure on the 6 Series is transmission shaft flexible coupling deteriorated. 15.3% of 6 Series models fail overall, based on 12,666 tests. Checking a car’s full MOT history before buying shows you recurring problems the seller might not mention.
More on the 6 Series
Other BMW car checks
Finance, stolen, write-off and owner history data provided by Experian. MOT data from DVSA. Known problems from GetCarWise analysis. Updated October 2026.